MODEM命令集 |
|
wnhoo
高階會員 ![]() ![]() ![]() ![]() 發表:75 回覆:443 積分:198 註冊:2003-04-22 發送簡訊給我 |
希望下面的资料,对大家有点帮助!
AT Commands A Answer Command
Bn Communications Options
D Dial Command
En Select Command Character Echo Option
Hn Control The Switchhook
I0 Identify The Product Code
I2 Perform ROM Checksum Test
I7 Version Number
Ln Select Speaker Volume Level
Mn Select Speaker Function Option
Nn Select Negotiate Handshake Option
On Go Online Command
P Select Pulse Dialing Method
Qn Select Result Code Option
Sn= Write To An S-Register
Sn? Read An S-Register
T Select Tone Dialing Method
Vn Select Response Format Option
Wn Select Extended Result Code
Xn Select Call Progress Option
Yn Select Long Space Disconnect Option
Zn Perform Soft Reset
&An Select Originate/Answer Role For Autoanswer
&Cn Select Data Carrier Detect Option
&Dn Select Data Terminal Ready Option
&F Load Factory Default Profile
&Gn Select Guard Tone Option
&Kn Select Flow ConTDol Option
&Pn Select Pulse Dialing Parameters
&Qn Select Communications Mode Option
&Rn Select RTS/CTS Option
&Sn Select Data Set Ready Option
&T0 Terminate Test In Process
&T1 Initiate Local Analog Loopback
&T3 Perform Local Digital Loopback
&T4 Enable Granting Of RDL Requests
&T5 Deny Granting Of RDL Requests
&T6 Initiate Remote Digital Loopback
&T7 Initiate RDL With Self Test
&T8 Local Loopback With Self Test
&T19 Perform RTS/CTS Cable Test
&Un Disable TDellis Coding
&V View Configuration Profiles
&Wn Store Active Profile
&Xn Select Sync TDansmit Clock Source
&Yn Select Stored Profile For Hard Reset
&Zn= Store Telephone Number
, Perform Pause
= Write To An S-Register
? Read An S-Register
P Select Pulse Dialing
T Tone S-Registers S0 Ring After Which To Answer
S1 Ring Count
S2 Hayes Escape Character
S3 Carriage Return Character
S4 Line Feed Character
S5 Backspace Character
S6 Wait Before Blind Dialing
S7 Wait For Carrier
S8 Pause Time For Comma
S9 Carrier Recovery Time
S10 Lost Carrier Hang Up Delay
S11 DTMF Dialing Speed
S12 Hayes Escape Guard Time
S16 Test in Progress
S18 Modem Test Timer
S19 AutoSync Options
S25 Detect DTD Change
S26 RTS To CTS Delay Interval
S30 Inactivity Timeout
S31 XON Character
S32 XOFF Character
S36 Negotiation Failure TDeatment
S37 Desired DCE Line Speed
S38 Hang-up Timeout
S43 Current Line Speed
S44 Framing Technique
S46 Protocol/Compression Selection
S48 Feature Negotiation Action
S49 Buffer Low Limit
S50 Buffer High Limit
S70 Maximum Number of ReTDansmissions
S73 No Activity Timeout
S82 Break Selection
S86 Connection Failure Cause Code
S91 Select Dial-up Line TDansmit Level
S95 Extended Result Code Bit Map
S97 V.32 Late Connecting Handshake Timing
S105 Frame Size
S108 Signal Quality Selector
S109 Carrier Speed Selector
S110 V.32/V.32 bis Selector
S113 Calling Tone ConTDol
S121 Use of DTD
S141 Detection Phase Timer
S142 Online Character Format
S144 Autobaud Speed Group Selection 风花雪月 e梦情缘
------
风花雪月 e梦情缘 |
jackkcg
站務副站長 ![]() ![]() ![]() ![]() ![]() 發表:891 回覆:1050 積分:848 註冊:2002-03-23 發送簡訊給我 |
MODEM命令集 的AT Commands是 公開制定的 但是 像 洛克威爾 或 摩托羅拉 的 語音晶片命令集 是各家晶片廠商 自定規格 以前 洛克威爾 有公開 資料 不過好像都找不到了 摩托羅拉 的部份 不知道有人知道嗎? 研究研究
討論討論 哈哈 *********************************************************
哈哈&兵燹
最會的2大絕招 這個不會與那個也不會 哈哈哈 粉好 Delphi K.Top的K.Top分兩個字解釋Top代表尖端的意思,希望本討論區能提供Delphi的尖端新知
K.表Knowlege 知識,就是本站的標語:Open our mind to make knowledge together!
希望能大家敞開心胸,將知識寶庫結合一起
------
********************************************************** 哈哈&兵燹 最會的2大絕招 這個不會與那個也不會 哈哈哈 粉好 Delphi K.Top的K.Top分兩個字解釋Top代表尖端的意思,希望本討論區能提供Delphi的尖端新知 K.表Knowlege 知識,就是本站的標語:Open our mind |
本站聲明 |
1. 本論壇為無營利行為之開放平台,所有文章都是由網友自行張貼,如牽涉到法律糾紛一切與本站無關。 2. 假如網友發表之內容涉及侵權,而損及您的利益,請立即通知版主刪除。 3. 請勿批評中華民國元首及政府或批評各政黨,是藍是綠本站無權干涉,但這裡不是政治性論壇! |